RB Publishing  

Sustainable, economical cleaning solvent for vapour degreasing in the aerospace industries

October 29th, 2021 2:13 pm | by Admin

The aircraft and aerospace component manufacturing industries face many critical cleaning applications during manufacturing processes and for finishing where surfaces need to be completely degreased leaving no residues. Although aqueous cleaning would seem to be the method of choice for environmental reasons with new advancements in cleaning solvent chemistry this is often not the case. Vapour degreasing is the most effective process, economical in use with lower energy uses, one tank needing less floor space than multi tank water-based systems and safe for users.

ProSolv®5408e has been developed to be used in place of the traditional chlorinated hydrocarbon solvents, trichloroethylene and perchloroethylene and those based on n-propyl bromide (nPb) which have been phased out for use as vapour degreasing solvents in the EU. The ProSolv®5408e advanced formulation, based on sustainable solvents, has been extensively tested with oils, soils greases and other contaminants from the manufacturing process and with is high KB value all these materials are easily removed to comply with aircraft standards for cleaning and degreasing to the highest levels. No titanium surface cracking or deleterious effects on other metals or composites commonly used for aircraft and aerospace component manufacture have been identified.

The innovative ProSolv 5408e formulation produced by Envirotech Europe ticks all the boxes with the perfect profile for vapour degreasing. Soft on the environment with near zero ozone depletion potential (ODP) and very low global warming potential (GWP), its lower boiling point at 48C minimises energy requirements giving reduced process times for greater throughput and comfortably handled critically cleaned parts. The incredibly low surface tension guarantees penetration into micron sized through and blind holes and between close contact surfaces.

Stable in use, ProSolv 5408e is safe for users with a high 8 hour occupational exposure level of 220 ppm. The solvent needs no additives or stabilisers and requires no testing. Sustainable, safe and secure for future use as your forever solvent.

Bonding of honeycomb sections for composites
An instance of critical cleaning is removal of all contamination from aluminium honeycomb prior to epoxy resin bonding of the formed aluminium skin to produce lightweight high tensile structures for applications such as leading edges on aircraft wings and wind turbine blades. This is an extremely demanding application, as any residues will prevent the adhesion of the adhesives leading to delamination with potentially disastrous effects.

Due to the high standards of cleaning which are required, this process is usually carried out by vapour/liquid degreasing with the traditional chlorinated solvents. However, due to the increasingly stringent controls on these materials, ProSolv®5408e which is fully tested to aircraft industry standards and with its greatly improved environmental and user profile is now increasingly used as the sustainable and safer replacement.

Cleaning for crack and fault testing of welds and castings
Another common use in the aircraft industry is in the cleaning of castings and metal fabrications before the use of NDT crack detection fluids. Removal of all surface contamination from manufacturing processes is vital to expose faults. Vapour degreasing and vapour liquid cleaning with ultrasonics is a favoured method, due to the excellent solubility of oils and greases and other soils using one tank with very fast processing and parts emerging completely clean and dry. Crack and fault detection in casting and welds is also important in other industries such as railways, automotive engines and turbines, where castings or critical welded fabrications are used. This is particularly relevant as part of the maintenance procedure for refurbishment of aircraft landing gear where surfaces can be heavily contaminated by hard to remove hydraulic oils, rubber and cement dust and grease.

As this application needs completely degreased, residue free and dry surfaces, the use of slow drying cleaners such as hydrocarbons or water-based cleaners may cause problems as the cracks need to be dry to allow penetration of the detection fluids. Vapour degreasing is the most effective cleaning system for all NDT applications as parts emerge dry from the cleaning process. ProSolv®5408e conforms to SaE-AMS2664 and E1417 99-1/7-1-1 solvent precleaning standard for Penetrant testing in aerospace applications.

Critical cleaning of oxygen and gas systems
Critical cleaning of oxygen lines and tanks where no organic residues can be tolerated is another ideal use for this new sustainable cleaning solution. ProSolv®5408e conforms to CGA, ELIGA and Compressed Gas Association standards for this application. A series of guides are available to using ProSolv®5408e for component cleaning to Oxygen standards and recommended cleaning methods involved, available on request.

ProSolv 5408e is produced to consistent quality standards worldwide and is available through a network of experienced and qualified suppliers.

For more information, visit https://www.vapour-degreasing.com/prosolv5408e.

EnviroTech Europe Ltd
Tel: 020 8281 6370
Email: contact@envirotech-europe.com


MecWash launches new website to showcase world-class systems

April 2nd, 2019 7:33 am | by Admin

Global leader in high performance aqueous cleaning technology, MecWash has launched a brand new website to showcase its range of aqueous parts cleaning and degreasing systems for a variety of specialist sectors.

As well as offering a modern new look, the website’s objective is to display the new cleaning technologies available, including the chemical design and specification, as well as the global servicing and support available by the specialist service engineering team. The bold navigation bar aims to provide a simple user experience for all, whether visitors are browsing for products specifically, or by sector.

Component cleanliness is undoubtedly a key quality criterion in numerous industries, with many requiring complete bespoke systems. MecWash is renowned for its unique, bespoke designs that cater to the needs of every sector in which it operates, delivering both value and productivity. Therefore, the addition of specialist sector pages was essential, including automotive, aerospace, fluid power, precision engineering and medical.

MecWash has a facility dedicated to chemistry and cleanliness analysis and chemical manufacture. This technical expertise lies at the heart of its approach to cleaning components. The new Chemical Considerations download allows customers to explore some of the main cleaning chemical products and applications.

MecWash is one of the leading designers and manufacturers of aqueous parts cleaning and degreasing systems. Its range of systems are used globally by companies with exacting standards. MecWash has a comprehensive and lasting commitment to its customers and the new site highlights the features, benefits and support opportunities that it offers.

John Pattison, managing director of MecWash Systems Ltd in Tewkesbury, Gloucestershire, comments: “We’re delighted with our new website. When initially discussing the site, we made sure we had our customers at the forefront of the design process. It was imperative for us to ensure customers had a user-friendly experience, with easily available information; be it by product or sector. We hope our customers are happy with the finished product.”

More details about MecWash and its range of world-class systems can be found on the new website: www.mecwash.com

MecWash Systems Ltd
Tel: 01684 271600
Email: enquire@mecwash.co.uk